Features:
Small size, 35x35mm mounting holes
6 PWM input channels for standard receiver or PPM SUM receiver
Up to 8-axis motor output
Supported 2-axis gimbal and auto trigger control
FTDI/UART port for upload firmware, debug, Bluetooth module or LCD display
I2C port for extend sensor, I2C LCD/OLED display or I2C-GPS NAV board for GPS and Sonar
Ultra low noise 3.3V LDO voltage regulator
ATMega 328P Microcontroller
MPU6050C 6 axis gyro/accel with Motion Processing Unit
HMC5883L 3-axis digital magnetometer
BMP085 digital pressure sensor
PCA9306DP1 logic level converter
NEO -6 GPS V3.1 Module
Features:
U-blox NEO-6M GPS module
5Hz update rate
32k I2C EEPROM for save configuration
Build in 25 x 25 x 4mm ceramic patch antenna
LNA and SAW chip
3.3V LDO low noise regulator
UART (TTL) port with EMI protection
3V lithium Rechargeable battery
Power and fix indicator LEDs
Reverse polarity protection for input power
Default parameter
Standard NMEA protocol
Baud rate: 9600
Nav rate: 1Hz
TIMEPULSE (fix LED) rate: 1Hz
Other
Dimension: 40 x 40 x 9mm
Weight: 16.4g/18.6g (include cable)
Hole diameter: 3.1mm
I2C-GPS NAV Module
Features:
All GPS data available via the I2C bus to connect to 328P Multiwii FC
A LED on board show GPS 3D Fix status
ATMega 328P Microcontroller
2 Molex 1.25mm 4Pin socket for GPS receiver and FC
2 port for ISP and FTDI
Other
Dimension: 20mmX30mm
Height: 5mm
Weight: 2.4g/5g (include cable)
Hole diameter: 3mm
Bluetooth parameter debug module
Features:
For Multiwii FC Configuration use with Android MultiWii Configuration
UART TTL socket
MultiWii Configuration function
Read and Write PID
Setting switch for AUX1 and AUX2
Monitor receiver signal and FC output signal
Monitor All sensors and GPS signal
Calibration Magnetometer and Accelerometer
Save and read profile
Default parameter
Baudrate: 115200
Module name: CRIUS_BT
Pair code: 0000
Other
Dimension: 15mmX37.5mm
Height: 5mm
Weight: 2.2g/3.9g (include cable)
Hole diameter: 3mm
FTDI USB-TTL Module
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector.
Package Including:
1x MWC V2.5 SE Flight Controller
1x I2C-GPS NAV Module
1x CN -06 GPS receiver
1x Bluetooth module
1x FTDI USB-TTL
Small size, 35x35mm mounting holes
6 PWM input channels for standard receiver or PPM SUM receiver
Up to 8-axis motor output
Supported 2-axis gimbal and auto trigger control
FTDI/UART port for upload firmware, debug, Bluetooth module or LCD display
I2C port for extend sensor, I2C LCD/OLED display or I2C-GPS NAV board for GPS and Sonar
Ultra low noise 3.3V LDO voltage regulator
ATMega 328P Microcontroller
MPU6050C 6 axis gyro/accel with Motion Processing Unit
HMC5883L 3-axis digital magnetometer
BMP085 digital pressure sensor
PCA9306DP1 logic level converter
NEO -6 GPS V3.1 Module
Features:
U-blox NEO-6M GPS module
5Hz update rate
32k I2C EEPROM for save configuration
Build in 25 x 25 x 4mm ceramic patch antenna
LNA and SAW chip
3.3V LDO low noise regulator
UART (TTL) port with EMI protection
3V lithium Rechargeable battery
Power and fix indicator LEDs
Reverse polarity protection for input power
Default parameter
Standard NMEA protocol
Baud rate: 9600
Nav rate: 1Hz
TIMEPULSE (fix LED) rate: 1Hz
Other
Dimension: 40 x 40 x 9mm
Weight: 16.4g/18.6g (include cable)
Hole diameter: 3.1mm
I2C-GPS NAV Module
Features:
All GPS data available via the I2C bus to connect to 328P Multiwii FC
A LED on board show GPS 3D Fix status
ATMega 328P Microcontroller
2 Molex 1.25mm 4Pin socket for GPS receiver and FC
2 port for ISP and FTDI
Other
Dimension: 20mmX30mm
Height: 5mm
Weight: 2.4g/5g (include cable)
Hole diameter: 3mm
Bluetooth parameter debug module
Features:
For Multiwii FC Configuration use with Android MultiWii Configuration
UART TTL socket
MultiWii Configuration function
Read and Write PID
Setting switch for AUX1 and AUX2
Monitor receiver signal and FC output signal
Monitor All sensors and GPS signal
Calibration Magnetometer and Accelerometer
Save and read profile
Default parameter
Baudrate: 115200
Module name: CRIUS_BT
Pair code: 0000
Other
Dimension: 15mmX37.5mm
Height: 5mm
Weight: 2.2g/3.9g (include cable)
Hole diameter: 3mm
FTDI USB-TTL Module
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 5V Arduino boards. It can also be used for general serial applications. The major difference with this board is that it brings out the DTR pin as opposed to the RTS pin of the FTDI cable. The DTR pin allows an Arduino target to auto-reset when a new Sketch is downloaded. This is a really nice feature to have and allows a sketch to be downloaded without having to hit the reset button. This board will auto reset any Arduino board that has the reset pin brought out to a 6-pin connector.
Package Including:
1x MWC V2.5 SE Flight Controller
1x I2C-GPS NAV Module
1x CN -06 GPS receiver
1x Bluetooth module
1x FTDI USB-TTL
- Brand New
- Mfg Part # PP1608
Payment Methods
Shipping
USPS, $9.50
Payment Policy
We could accept the payment through paypal
Shipping Policy
We ship out the goods by airmail with registered services.
Return/Exchange Policy
We have a well developed RMA system. The buyer could return the goods to us within 30 days from the date of purchase of the products.
Product(s) can be returned for exchange or refund, provided the product(s) is returned in new and original condition with original product packaging and labels.
Please Login or Register first before asking a question.
